Home » How To Make a Sliding Plexiglass Window for Your Deer Blind

How To Make a Sliding Plexiglass Window for Your Deer Blind

If you’re looking to improve your deer hunting experience, a sliding Plexiglass window is a great way to do it. With this type of window, you can see right through it to the inside of your blind, andhunters can watch the deer as they come in or out. It’s an easy way to increase your chances of success when hunting deer.

How to Make Your Own Sliding Plexiglass Window

If you’re looking for a way to make your deer blind more accessible for hunting, a sliding Plexiglass window could be just what you need. By installing a sliding window, you’ll be able to get a better view of your surroundings without having to get up from your chair.

Here’s how to make a sliding Plexiglass window:

1. First, find a piece of Plexiglass that measures the same size as the opening in your deer blind. Cut the Plexiglass to fit, and then use some silicone adhesive to attach it to the inside of the deer blind opening.

2. Next, measure and cut a piece of cardboard that’s slightly larger than the Plexiglass. Glue the cardboard onto the back of the Plexiglass, making sure that it’s aligned with the edges of the Plexiglass.

3. Now slide the Plexiglass into position, and use screws or nails to attach it to the back of the cardboard. Make sure that the screws or nails are positioned so that they don’t protrude through the front of the Plexiglass.

4. Finally, fill your deer blind with fresh hay or leaves, andyou’re ready to hunt!

Outer Size of the Blind

The outer size of the deer blind should be determined by the width of the opening and the height of the blind. The blind should be large enough to fit through the opening and cover the entire opening. A good rule of thumb is to make the blind at least twice as wide as the opening.

When installing a sliding Plexiglas window, it is important to follow these tips:

1. Clean and dry all surfaces before installation.
2. Insert a straight edge into one corner to create a consistent frame for your window.
3. Center your Plexiglass Window on this frame and mark both ends with a pencil or pen. This will help when measuring and trimming your window later on.
4. With a sharp knife, carefully cut out your Plexiglas Window from the opposite end of your marked line-be sure not to cut into your straight edge!
5. Smooth out any rough edges with a file or sandpaper.

6. Reposition your Plexiglas Window and attach it to the opposite end of the frame with a few screws or nails.

7. Enjoy your new window!

Frame Size and Length of Your Sliding Plexiglass Window

If you want to make a sliding Plexiglass window for your deer blind, you will need to first calculate the size of the window that you need. The size of the window will be based on the height of your deer blind and the width of the opening on the side of your blind.

To calculate the size of the window, measure both the height and width of the opening on one side of your blind. Add these measurements together to get a total width. Then, add 2 inches to this number to account for the thickness of the Plexiglass. Finally, measure the height of your deer blind and divide this number by 2. This will give you the length of Plexiglass that you need.

Once you have calculated the size of the window, cut out a piece of Plexiglas that is equal to these dimensions. Be sure to measure each piece of Plexiglas carefully so that they fit perfectly into their respective openings on your deer blind. Once you have cut out all of your Plexiglas pieces, install them using screws or nails that are long enough so that they can be pulled out after installation is complete.

Now that your sliding Plexiglass window is installed, itis time to add the curtain that will cover it. You can purchase a pre-made curtain or you can make your own curtain using a sheer fabric and a zipper or lace closure.

How to Install your Sliding Plexiglass Window

Making a sliding Plexiglass window for your deer blind is simple and can be done in a few hours. The key is to use the right materials and have patience while installing the window. Here are the steps:

1) Measure the width of the opening you want to create in your deer blind and cut a piece of Plexiglas that is that width. Make sure to account for any gaps between the walls of your deer blind.

2) Trace the outline of your window onto the Plexiglas with a pencil. Be sure to leave enough room around the edges so that you can screw it onto the wall of your deer blind.

3) Mark where the screws will go into the Plexiglas, then drill holes that are slightly larger than the screws. Once you have drilled all of the holes, insert the screws into them.

4) Place the Plexiglas window onto your wall of your deer blind, making sure that it is positioned exactly where you marked it on the Plexiglas. Then, use a hammer and nails to secure it into place.

5) Finally, use a saw to cut out a hole in one of the sides of your deer blind so that youcan see out.

Recommendations

1) Make sure that the area around your blind is clear of obstacles before beginning construction. A fence or other nearby structure could block your view and ruin your day hunting! Also be aware of any trees or branches within range of your blind that might fall on your window during a storm. Be safe and err on the side of caution when it comes to this aspect of your build.

2) Use quality materials when constructing your deer blind – poor construction can lead to problems down the road and may even void your warranty. We recommend using high-quality materials like thick Plexiglas or heavy-duty aluminum.

3) If you are planning to use awnings or other coverings for your blind, be sure to measure and customize them before construction begins. A proper fit will ensure that you enjoy a comfortable hunting experience all season long!

4) Finally, take the time to properly set up your deer blind when you first get it ready for use. This will ensure that everything goes smoothly from start to finish.

myhomedezines

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top